Model |
|
PD-150-3.3 |
PD-150-5 |
PD-150-12 |
PD-150-15 |
PD-150-24 |
PD-150-48 |
Output |
DC Output |
3.3V |
5V |
12V |
15V |
24V |
48V |
Rated Current |
30A |
26A |
12.5A |
10A |
6.5A |
3.3A |
Current Range Note 2 |
0~30A |
0~26A |
0~12.5A |
0~10A |
0~6.5A |
0~3.3A |
Ripple and Noise Note 3 |
80mV |
80mV |
120mV |
120mV |
120mV |
200mV |
Voltage ADJ. Range |
± 10% of rated output voltage |
Voltage Accuracy |
± 3% |
± 2.0% |
± 1.0% |
± 1.0% |
± 1.0% |
± 1.0% |
Line Regulation |
± 0.5% |
± 0.5% |
± 0.5% |
± 0.5% |
± 0.5% |
± 0.5% |
Load Regulation |
± 3.0% |
± 1.0% |
± 1.0% |
± 1.0% |
± 1.0% |
± 1.0% |
Set-up Time |
<=2.0S (120Vac input, Full load); <=1.0S (230Vac input, Full load) |
Hold up Time |
>=10mS(120Vac input, Full load); >=20mS(230Vac input, Full load) |
Temperature Coefficient |
± 0.03% /℃ |
Overshoot and Undershoot |
<5.0% |
Input |
Voltage Range |
88Vac~132Vac/176Vac~264Vac |
Frequency Range |
47Hz~63Hz |
Efficiency ( Typical) |
115Vac |
73% |
78% |
83% |
83% |
84% |
85% |
230Vac |
74% |
79% |
83% |
84% |
85% |
86% |
AC Current (max.) |
3.5A |
3.5A |
4.0A |
4.0A |
4.0A |
4.0A |
Inrush Current (Typical) |
20A@120Vac; 40A@230Vac Cold start |
Leakage Current |
<3.5mA |
Protection |
Over Current |
105%~150% of rated output current,auto recovery |
Over Voltage |
120%~150% of rated output voltage,auto recovery |
Shorted Circuit |
Long-term mode, auto recovery |
Environment |
Operating amb. Temp. & Hum. |
-2℃~70 ; 20% ~90% RH No condensing(refer to the derating curve)℃ |
Storage Temp. & Hum. |
-40 ~85 ; 10% ~95% RH No condensing℃ ℃ |
Safety & EMC Note4 |
Safety Standards |
UL60950-1 |
Withstand Voltage |
Primary-Secondary:3.0KVac; Primary-PG:1.5KVac; Secondary-PG:0.5KVDC |
Isolation Resistance |
100M ohms |
EMC standards |
EN55022 Class B;EN-61000-3-2,3,EN61000-4-2,3,4,5,6,8,11,ENV50204,EN61000-6-2 |
Others |
MTBF (MIL-HDBK-217F) |
More than 100, 000Hrs (25 , Full load)℃ |
Dimension (L*W*H) |
198× 98× 38mm |
Connection |
7P/8.025mm barrier terminal block |
Cooling method |
Cooling by free air convection |
Note |
1. All parameters NOT specially mentioned are measured at rated input, rated load and 25 of ambient temperature.℃2. De-rating according to operating ambient temperature and input AC voltage, Please check the de-rating curve for more details information. 3. Measured at 20MHz of bandwidth by using a 12” twisted pair-wire terminated with a 0.1 uF & 47uF parallel capacitor. 4. The SPS is considered a component which will be installed into final equipment. The equipment must be re-confirmed that it still meets EMC directives. |
